Acer Incorporated ... AC97 Modem Controller

27 risposte [Ultimo messaggio]
Ritratto di amicon
amicon
(Junior)
Offline
Junior
Iscritto: 24/07/2006
Messaggi: 11

Quote:

divine_pegasus ha scritto:
Ragazzi non riesco andare sul lito di linmodem...dove posso trovare scanmodem se non sul sito che avete segnalato??
grazie per e risposte...

http://linmodems.technion.ac.il/packages/
Io ci riesco, se mandi un indirizzo di e-mail te lo allego, sono 72k.

Ciao, Amicon.

Ritratto di divine_pegasus
divine_pegasus
(Junior)
Offline
Junior
Iscritto: 07/01/2005
Messaggi: 30

Il problema era dato dal fatto che il sito è stato giù per qualche ora... poi sono riuscito a scaricare scanModem.
Dopo aver avviato scanModem che mi da questi risultati

Welcome to SUSE LINUX 10.0 (i586) - Kernel
on System with processor: i686
currently under kernel: 2.6.13-15-smp
Be sure to read the Ethernet section of Modem/YourSystem.txt
A /dev/modem symbolic link is not present
USB modem not detected.

Checking for audio card modem support
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] Sound Controller (rev a0)
Reading /proc/asound/pcm
00-00: Intel ICH : SiS SI7012 : playback 1 : capture 1
00-01: Intel ICH - MIC ADC : SiS SI7012 - MIC ADC : capture 1
The potentially supporting audio + modem drivers now loaded on this System are:
0 snd_intel8x0

The kernel was assembled with compiler: 4.0.2
No compiler installed.
a gcc-4.0.2 package must be installed to support driver compiling
This is a new compile requirement case.
-------------
Found make utility.
-------------
Checking for kernel-headers needed for compiling.
Kernel-headers supporting compiling are resident:

Modem candidates are at PCI_buses: 00:02.6

Providing detail for device at 00:02.6
with vendor-ID:device-ID
----:----
Class 0703: 1039:7013 Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev a0) (prog-if 00 [Generic])
SubSystem 17c0:1059 Wistron Corp.: Unknown device 1059
Flags: medium devsel, IRQ 11
Checking for IRQ 11 sharing with modem.
XT-PIC ohci1394, SiS SI7012, ohci_hcd:usb1, ohci_hcd:usb2, ohci_hcd:usb3, ehci_hcd:usb4, yenta, yenta, eth0

-----PCI_IDs------- --CompilerVer-
Feature List: Primary Subsystem Distr KernelVer kernel default CPU
./scanModem test 1039:7013 17c0:1059
Welcome 2.6.13-15-smp 4.0.2 none i686
From records, 17c0:1059 has soft modem codec type SIL27

Get the package from http://linmodems.technion.ac.il/packages/smartlink/
Open a terminal and unpack under Linux with:
$ tar zxf .
and read the Quick Instructions at the beginning of file 1st_Read.txt in new folder SLMODEMD.gcc4/ .
Briefly, the following two Root commands should set up the modem:
modprobe snd-intel8x0m
slmodemd --alsa -c YOUR_COUNTRY modem:1
which should create ports:
/dev/ttySL0 --> /dev/pts/N , with N some number
Find YOUR_COUNTRY from the listing displayed by:
slmodemd --countrylist

The controller: 1039:7013 SIS 630
is capable of supporting soft modem chips from AT LEAST manufacturers:
Pctel
AgereSystems
Conexant
Intel
Smartlink

The Subsystem PCI id does not itself identify the modem Codec.

Checking for autoloaded ALSA modem drivers

Driver snd-intel8x0m may enable codec acquisition
=== Begin mc97 codec query ===
the MC97 file is: /proc/asound/card1/codec97#0/mc97#1-1
--------
1-1/0: Silicon Laboratory Si3036,8 rev 7

Extended modem ID: codec=1 LIN1
Modem status : GPIO MREF ADC1 DAC1 PRE(ADC2) PRF(DAC2) PRG(HADC) PRH(HDAC)
Line1 rate : 8000Hz
--------
from /proc/asound/card1/codec97#0/mc97#1-1+regs
0:7c = 5349
0:7e = 4c27
Translating into: SIL27
an AgereSystems codec
=== End mc97 codec query ===

Beginning check for older ac97_codec modems.
An older ac97_modem codec was not detected.

Agreement between diagostic and Archive data.
The Subsystem has an Agere Systems codec SIL27

The modem can be set up by Root commands:
modprobe snd-intel8x0m
slmodemd --alsa -c YOUR_COUNTRY modem:1

The ALSA modem driver snd-intel8x0m provides low level hardware access.
The slmodemd provides high level functions and is not kernel-version specific.
From http://linmodems.technion.ac.il/packages/smartlink/ follow the link

Also download the ungrad-winmodem.tar.gz and the http://linmodems.technion.ac.il/packages/unloading.gz
Within the SLMODEMD package the 1st_Read.txt gives instructions
For guidance on bootup automation see:
http://linmodems.technion.ac.il/archive-fifth/msg04652.html

Read Modem/Slmodem.txt instruction for doing the slamr diagnostic.
== Checking PCI IDs through modem chip suppliers ==

SmartLink at http://www.smlink.com/ owns vendor IDs 163c, 2000, 2003, and 2004
The official download site is: http://www.smlink.com/main/index1.php?ln=en&main_id=40
But a more recent code and a much broader license for other chipset support,
can be downloaded from http://linmodems.technion.ac.il/packages/smartlink/
Though not always needed, download the files:
slmodem-CurrentVersion.tar.gz - provides the most general code package.
SLMODEMD.gcc4 - provides a compiled slmodemd
ungrab-winmodem.tar.gz - may be needed for usage with slamr.
Details on their usage are in Slmodem.txt, Slmodem-ALSA.txt and
http://linmodems.technion.ac.il/slmodem-serial.html

== Checking PCI IDs through modem chip suppliers ==
Vendor 1039 is SiS, Silicon Integrated System, producing soft modem controllers and subsystems.

======= PCI_ID checking completed ======
Update=2006_July_27

Analyzing information for PCMCIA device at PCI Bus 00:09.0
00:09.0 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01)
Subsystem: Wistron Corp.: Unknown device 3202
Flags: bus master, medium devsel, latency 168, IRQ 11
GREPping for an inserted PCMCIA modem with filter: ommunication

Analyzing information for PCMCIA device at PCI Bus 00:09.1
00:09.1 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01)
Subsystem: Wistron Corp.: Unknown device 3202
Flags: bus master, medium devsel, latency 168, IRQ 11
GREPping for an inserted PCMCIA modem with filter: ommunication
If a PCMCIA modem is currently inserted and the sockets activated by
/etc/init.d/pcmcia start
then the PCMCIA bridge is NOT transparent.

If the modem is known to have a Lucent digital signal processing chipset,
then PCMCIA.tar.gz variant assembled by Joern Wustenfeld is necessary,
rather than the standard ltmodem-.tar.gz at http://ltmodem.heby.de/
drwxr-xr-x 2 root root 700 2006-07-30 22:27 /dev/.udevdb

There is an active UDEV file system, creating device nodes in volatile RAM.
For SmartLink modems using the slamr.ko or slusb.ko drivers an /etc/init.d/ script
will be necessary to create /dev/slamr0 or /dev/slusb0 ports, or manually by:
# mknod -m 600 /dev/slamr0 c 242 0
# mknod -m 600 /dev/slusb0 c 243 0
upon each bootup.

For information on modem port creation under the UDEV device file system see:
http://linmodems.technion.ac.il/archive-fourth/msg03299.html for Conexnant modems
http://linmodems.technion.ac.il/archive-fifth/msg01177.html for Lucent/Agere DSP modems

Checking for modem symbolic link support lines within /etc/udev/ files

The kernel-2.6.13-15-smp was compiled with CONFIG_REGPARM, providing more compact and faster code.

The Major.Minor versions differ in the designated compiler none and the 4.0.2 used in kernel assembly!!"
But there must be a match on the target for driver installation,
of gcc Major.Minor versions or kernel and drivers!!
Otherwise the drivers will fail to load with warning:
Invalid module format!!"
See http://linmodems.technion.ac.il/archive-fifth/msg04252.html

A /dev/modem symbolic link is not set.

The following information blocks just query some ppp support items.

====================================================
grep -rs ppp /etc/modprobe.*
-------------------------------------
/etc/modprobe.conf:# ppp over ethernet
/etc/modprobe.conf:# the kernel 2.2 uses pppox
/etc/modprobe.conf:# the kernel 2.4 uses pppoe
/etc/modprobe.conf:alias char-major-108 ppp_generic
/etc/modprobe.conf:alias char-major-144 pppoe
/etc/modprobe.conf:alias net-pf-24 pppoe
/etc/modprobe.conf:# the kernel 2.2 uses ppp.o as ppp driver,
/etc/modprobe.conf:# the kernel 2.4 uses ppp_generic.o
/etc/modprobe.conf:alias ppp0 ppp_generic
/etc/modprobe.conf:alias ppp1 ppp_generic
/etc/modprobe.conf:alias tty-ldisc-3 ppp_async
/etc/modprobe.conf:alias ppp-compress-18 ppp_mppe
/etc/modprobe.conf:alias ppp-compress-21 bsd_comp
/etc/modprobe.conf:alias ppp-compress-24 ppp_deflate
/etc/modprobe.conf:alias ppp-compress-26 ppp_deflate
-------------------------------------
Resident PPP support modules are properly uncompressed .
----active COMM services are ------------
eth0 Link encap:Ethernet HWaddr 00:0A:E4:42:50:29
inet6 addr: fe80::20a:e4ff:fe42:5029/64 Scope:Link
This COMM mode should be closed before using the modem, or DNS services may fail.
---- dmesg queries -------
Kernel command line: root=/dev/hda9 vga=0x317 selinux=0 resume=/dev/hda8 splash=silent acpi=off noapic
ACPI: Interpreter disabled.
pnp: PnP ACPI: disabled
apm: BIOS not found.
audit: initializing netlink socket (disabled)
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001

Welcome is not yet providing pre-compiled drivers for WinModems

=========================================

ho seguito i vari passi ovvero ho letto le quick instruction e fatto quello che dicevano, poi ho dato i comandi

modprobe snd-intel8x0m
slmodemd --alsa -c ITALY modem:1

ed ho ricevuto come output

linux:/home/solid_snake/modem/inmod/insmod/SLMODEMD.gcc4 # slmodemd --alsa -c ITALY modem:1
SmartLink Soft Modem: version 2.9.11 Mar 13 2006 18:27:33
symbolic link `/dev/ttySL0' -> `/dev/pts/2' created.
modem `modem:1' created. TTY is `/dev/pts/2'
Use `/dev/ttySL0' as modem device, Ctrl+C for termination.

subito dopo ho provato a fare la connessione e questo è il log:

SuSE Meta pppd (smpppd-ifcfg), Version 1.59 on linux.
Status is: disconnected
trying to connect to smpppd
connect to smpppd
Status is: disconnected
Status is: connecting
pppd[0]: Plugin passwordfd.so loaded.
pppd[0]: --> WvDial: Internet dialer version 1.54.0
pppd[0]: --> Initializing modem.
pppd[0]: --> Sending: ATM1
pppd[0]: ATM1
pppd[0]: OK
pppd[0]: --> Sending: ATX3
pppd[0]: ATX3
pppd[0]: OK
pppd[0]: --> Modem initialized.
pppd[0]: --> Sending: ATDT7020187187
pppd[0]: --> Waiting for carrier.
pppd[0]: ATDT7020187187
pppd[0]: NO CARRIER
pppd[0]: --> No Carrier! Trying again.
pppd[0]: --> Sending: ATDT7020187187
pppd[0]: --> Waiting for carrier.
pppd[0]: ATDT7020187187
pppd[0]: NO CARRIER
pppd[0]: --> No Carrier! Trying again.
pppd[0]: --> Sending: ATDT7020187187
pppd[0]: --> Waiting for carrier.
pppd[0]: ATDT7020187187

Cos'è che non funziona? e soprattutto cos'è quelòl' ATDT prima del numero da comporre? grazie in anticipo per l'aiuto

Ritratto di sunrots
sunrots
(Guru)
Offline
Guru
Iscritto: 04/01/2005
Messaggi: 510

L'utente Pegasus dovrebbe cortesemente proseguire la discussione aprendo un altro post con il titolo specifico per il suo modem (SiS) . In questo modo altri utenti con la stessa periferica potranno rintracciare la discussione ed avvantaggiarsi della eventuale soluzione.
Grazie,

sunrots

Non più attivo qui. Mi troverete su http://it-opensuse.org Wink

Ritratto di amicon
amicon
(Junior)
Offline
Junior
Iscritto: 24/07/2006
Messaggi: 11

Quote:

Io ho scritto:
Grazie, stasera riprovero` con slmodem etc. etc. dopo aver ripulito tutto.

Circa il modem muto, so che potrebbe essere una cretinata, ma prova queste due piccole cose :
1) in /etc/wvdial.conf inserisci la riga "Setvolume = 3" (o 4 o 5)

2) guarda se in KMix il volume di "phone" e` alzato (e selezionato)

Ti faccio sapere gli sviluppi del mio modem.

Per quel che mi riguarda, nulla di nuvo sotto il sole, sto impazzendo come mai mi e` capitato con linux... bah... se qualcuno ha ancora qualche idea, ben vengano.

Orion, sei riuscito a far cantare il tuo modem ?

Ciao, Amicon.

Ritratto di sunrots
sunrots
(Guru)
Offline
Guru
Iscritto: 04/01/2005
Messaggi: 510

Salve,
è possibile dare una occhiata a come viene identificato il modem sotto Win? Sad
Inoltre, ho dato una occhiata al file SLMODEMD.gcc4.tar.gz.
Confermate di aver cambiato i permessi per il file od i files che devono poi essere utilizzati? Ho visto la proprietà del file è del gruppo e dell'utente "marv", mentre per voi dovrebbero essere ovviamente "root" od "users"

Saluti
sunrots

Non più attivo qui. Mi troverete su http://it-opensuse.org Wink

Ritratto di orion
orion
(Guru)
Offline
Guru
Iscritto: 11/07/2006
Messaggi: 2919

Io non ho ottenuto alcun miglioramento. Il modem rimane sempre muto e non riesce a comporre il numero.

Ora, da windows (uhh, quanto tempo che non lo avviavo, l'antivirus mi ha tirato giu` una quantita` atroce di aggiornamenti Big Grin ), ho ottenuto le seguenti informazioni sul modem: http://img524.imageshack.us/img524/8363/modemoj7.jpg

openSUSE 12.1 on Acer Aspire 1810tz - LXDE ultima versione dal repo x11:/lxde

Ritratto di sunrots
sunrots
(Guru)
Offline
Guru
Iscritto: 04/01/2005
Messaggi: 510

Quote:

orion ha scritto:
Ora, da windows ho ottenuto le seguenti informazioni sul modem: http://img524.imageshack.us/img524/8363/modemoj7.jpg

Dopo aver visto l'immagine e la persistente presenza della sigla CXT, avrei dei forti sospetti sul fatto che...si debba utilizzare il driver Conexant !
A questo indirizzo, che è un tutorial alla installazione dei winmodem, si dà una spiegazione di tale arcano...
http://libre-fan.apinc.org/article38.html
Speriamo si tratti di questo.
Fate sapere, grazie

sunrots

Non più attivo qui. Mi troverete su http://it-opensuse.org Wink